Sunforce Products 45455 30 Foot Tower Kit for the 600 Watt Wind Turbine and TVCoverups SBX1042BR 42 Inch Flat Panel TV Box, Remote Controlled, 6.25 Inch Depth

Sunforce Products 45455 30 Foot Tower Kit for the 600 Watt Wind Turbine and TVCoverups SBX1042BR 42 Inch Flat Panel TV Box, Remote Controlled, 6.25 Inch Depth

Sunforce Products 45455 30 Foot Tower Kit for the 600 Watt Wind Turbine

Sunforce Products 45455 30 Foot Tower Kit for the 600 Watt Wind Turbine

  • The Sunforce Products 45455 30 Foot Tower Kit was designed specifically for your Sunforce Products Wind Turbine. Small increases in average wind speeds result in dramatic increases in energy output of the wind generator. For example, an increase in wind speeds of 10% (9 mph – 10 mph; 4 m/s – 4.5 m/s) results in approximately a 30% increase in the power available from the wind. Therefore, the better the location the better the performance. As a rule, the wind generator should be mounted as high and as far away from obstructions as possible. This will create a clear wind channel. This guy-wire supported tower utilizes lightweight tubing while providing safety and strength. Two people can easily erect this tower in about an hour. Because the wind generator and tower are lightweight, no winches or vehicles are required for installation. The tower includes a simple yet effective tower base and anchoring system, which eliminates the need for a concrete base-pad. Depending on your soil conditions, cement may be necessary for proper anchoring. There are no moving parts in the tower, so maintenance is minimal.

  • Tower Base
    Lower Guy Cable Wire: 21 ft (6.4 m)
    Upper Guy Cable Wire: 30 ft (9.1 m)
    Guy Wire Attachment Plates
    Cable Clamps (16)
    Cable Thimbles (8)
    Arrowhead Earth Anchor
    Tower Base Earth Spikes
    Earth Anchor Driving Rod
    Tower Tubes: (1) 42 in (1.0 m); (1) 48 in (1.2 m); (4) 72 in (1.8 m)
Price: $437.50

TVCoverups SBX1042BR 42 Inch Flat Panel TV Box, Remote Controlled, 6.25 Inch Depth

TVCoverups SBX1042BR 42 Inch Flat Panel TV Box, Remote Controlled, 6.25 Inch Depth

  • The TVCoverUp is a novel, simple and elegant way to conceal a flat screen television. With a TVCoverUp, a television screen is no longer a stark center of attention, detracting from a room’s decor. Instead, framed art provides the focal point – until it deftly swings upward to reveal the television hidden beneath.

    The Automated RF Remote Control unit opens and closes by a radio frequency remote control, which activates two 12VDC actuators. Two micro limit switches are provided to cut the power to the actuators unless the TV is in a fully retracted position, when using automatic tilting or articulating TV mounts.

    Max TV Measurements: 40.75″ x 28.5″

    The RF Remote Controlled, 6.25″ Depth Box is also built to accommodate various sized TV’s:

    • Up to 37 Inches
    • Up to 50 Inches
    • Up to 55 Inches
    • Up to 65 Inches

    The TVCoverups mechanisms are installed within the provided Installation box and are lifting two 3/4″ channel aluminum bars, 2 1/2 inches wide that is hinged to the mechanism. The arms are retrofitted “into” the panel being sent. The panel is light weight (1lb/sqft), consisting of five layers including 1/4″ pressboard face, 3mm Dibond (dual sided aluminum sheet with a rubber core), 1/2″ wood frame, with 1/4″ gator board covered with Black linen for the backing. This system removes any stress from an otherwise fragile picture frame or box canvas. It is best to keep the total weight, including the panel, within the 45 pound range.

    The installation box consists of a back and four sides, some minor assembly required.

  • Specifications
    Manufacturer TVCoverups
    Manufacturer Product No. SBX1042BR
    UPC 851396004383
    Installation Box O.D. 47.25″ W x 33″ T x 7″ D
    Panel Size 48.375″ W x 34″ T
    • 1x – 42 Inch Flat Panel TV Box, RF Remote Controlled, 6.25 Inch Depth
    • 1x – Lifting Panel to mount artwork upon
    • 2x – Automated Lift hardware
    • 4x – Screws to attach artwork
    • 1x – Remote Control
    • 1x – Owner’s Manual
Price: $3,441.00

Leviton 80414-E Decora Blank Fill Plate, Black

Leviton 80414-E Decora Blank Fill Plate, Black

  • Whether you’re involved in new-home construction, renovating, or just upgrading your decor, it’s often difficult to anticipate the final needs of a home. If you’re installing a Decora-style single- or multi-gang wall plate to house your switches, dimmers and outlets but are not yet ready to install the appropriate insert, the Decora Blank Fill Plate will provide an attractive, discreet replacement as an unassuming, temporary fix. Decora-style wall plates are sold separately.

    These blank plates also lend them themselves to some custom use only you might dream up – drill it out to fit your bank of LEDs or special switch, perhaps?

    The Decora Blank Fill Plate is also available in almond, white and ivory.

  • Specifications

    Leviton Product No.: 80414-E
    UPC: 078477789988
    Dimensions: 4 1/16″ H x 1 7/16″ W
    Insert Type: Blank
    Opening Type: Decora
    Approvals: UL and CSA compliant
    Warranty: 1 year, limited

    • Wall plate insert
    • Mounting screws
Price: $3.56